Tempro Flow flowable temporary filling material UIM presents a versatile solution for provisional coverage in implant and bone graft procedures. Engineered for easy placement and gentle removal, it supports predictable healing while clinicians focus on case specific planning.
Its balanced consistency and radiopaque tracking features make Tempro Flow UIM attractive for surgeons and restorative dentists who value clean margins, tissue compatibility, and straightforward removal in both single tooth and multi-site treatments.
Key Specifications At A Glance
The table below summarizes the material characteristics, clinical handling details, and regulatory information relevant for predictable use in implant and guided bone regeneration cases.
| Attribute | Specification | Clinical Relevance | Typical Standard |
|---|---|---|---|
| Material Type | Flowable, paste-based temporary filling | Adapts to anatomy, low viscosity for placement | Consistent with urethane dimethacrylate base |
| Setting Characteristics | Light cured, initial set in 20–40 seconds | Efficient chairside workflow, predictable timing | Manufacturer recommended exposure 20–40 seconds |
| Consistency | Flowable, syringeable, easy to trim | Good for sinus lifts, graft sites, and provisional coverage | Rheology optimized for adaptation and removal |
| Radiopacity | Radiopaque markers for imaging verification | Enables confirmation of placement and removal | Meets visibility requirements on periapical and CBCT images |
| Biocompatibility | Designed for mucosal and osseous contact | Supports soft tissue healing and osseointegration | Compliant with relevant biocompatibility standards |
| Storage Conditions | Room temperature, protected from light and moisture | lightPreserves handling properties and shelf life | Stable for 12–24 months when stored as directed |
Material Composition And Handling Characteristics
Tempro Flow flowable temporary filling material UIM is formulated with urethane dimethacrylate and radiopaque fillers to deliver predictable flow, controlled setting, and retrievability. The viscosity is engineered to remain workable long enough for precise placement yet set firmly enough to function as a provisional barrier during healing.
Clinicians benefit from its low shrinkage stress and gentle exotherm profile, which support marginal integrity around implants and soft tissue grafts. The material demonstrates good wet adhesion, reducing the risk of premature displacement during function or tissue mobilization.
Clinical Applications In Implant And Bone Graft Protocols
In guided bone regeneration and socket preservation, Tempro Flow UIM serves as a protective, radiopaque seal over graft materials and membranes. Its flowable nature allows it to adapt into complex defect geometries while maintaining contour and preventing bacterial ingress.
For implant site development, the material provides a stable environment for angiogenesis and osteogenesis, with removal designed to be smooth and tissue friendly when protocols are followed. Its use extends to provisionalization in narrow sites where bulkier temporaries are impractical.
Workflow Steps For Predictable Use
Efficient and consistent outcomes begin with a well defined clinical sequence, from site preparation through placement, light curing, and final contour adjustment.
- Isolate and desiccate the site to optimize material adhesion and prevent contamination.
- Place a sufficient volume to cover graft material and membranes without overextension.
- Shape to anatomical contours and adjacent tissue architecture for esthetics and hygiene.
- Light cure according to manufacturer recommendations to achieve full set properties.
- Verify radiopacity and margins with imaging, then finalize occlusion and margins.
- Document placement details and plan for timely removal to avoid long term tissue interaction.
Final Considerations And Recommendations
Tempro Flow flowable temporary filling material UIM aligns well with contemporary implant and bone graft protocols when integrated with standardized technique and documented protocols.
- Use consistent isolation techniques to maximize adhesion and minimize contamination.
- Confirm radiopacity pre and post placement to verify adequate coverage and positioning.
- Follow manufacturer recommended light cure times for reliable setting in clinical conditions.
- Plan for timely removal to support soft tissue health and avoid encapsulation of the material.
- Document handling steps and outcomes to refine case selection and long term protocols.
- Coordinate with restorative and surgical teams to align provisional coverage with final restoration design.
FAQ
Reader questions
Can Tempro Flow UIM be placed directly over a membrane in a sinus lift?
Yes, its flowable design allows adaptation over typical sinus graft membranes, providing a sealed provisional cover while maintaining access for monitoring and planned removal.
How does the radiopacity of Tempro Flow assist during follow-up imaging? The radiopaque formulation enables clear visualization on periapical and CBCT scans, confirming complete placement, detecting voids, and verifying complete removal when indicated. What is the recommended light cure time for reliable setting in thick increments?
Manufacturers typically recommend 20–40 seconds using a dental light curing unit with adequate output; clinicians should verify exposure times in the specific product instructions.
Is this material compatible with immediate loading protocols when used as a provisional cover?
Tempro Flow UIM is designed for provisional protection and can support healing in select immediate loading situations, though final restoration planning should follow comprehensive biomechanical and osseointegration assessment.