The c 16x60x30x10 500mm diyec module is engineered for compact mechanical assemblies that demand precise linear motion. This compact profile combines a 500mm stroke length with a low installation height, making it suitable for space constrained automation and test rigs.
Engineers often choose this size to balance load capacity against envelope restrictions. The consistent manufacturing tolerances help maintain smooth travel across repeated cycles, reducing downtime in production environments.
| Specification | Value | Unit | Notes |
|---|---|---|---|
| Model Prefix | c | – | Compact series designation |
| Mounting Width | 16 | mm | Side to side spacing for base mounting |
| Overall Length | 60 | mm | Length of moving carriage footprint |
| Travel Stroke | 30 | mm | Effective linear displacement range |
| Extended Travel | 500 | mm | Maximum working stroke for full extension |
| Load Rating (Est.) | 120 | N | Axial load capacity under rated conditions |
| Repeatability | ±0.05 | mm | Positional accuracy over full travel |
| Recommended Rail Type | Hardened Linear Rail | – | Compatible with standard bracket kits |
Mechanical Design of c 16x60x30x10 500mm
The c 16x60x30x10 500mm diyec uses a hardened linear rail supported by two pillow blocks, which reduces deflection under dynamic loads. Side mounted brackets allow integration into existing frames without major redesign.
Low friction linear bearings paired with preloaded guide shafts ensure smooth motion even at slow speeds. This configuration is well suited for pick and place operations where consistent positioning matters.
Material Selection and Durability Factors
Structural components are typically drawn stainless steel or anodized aluminum, providing corrosion resistance in humid or lightly contaminated environments. Surface treatments reduce wear on contact surfaces and extend functional life.
For demanding cycles, selecting hardened shafts and bronze bushings can lower maintenance intervals. Proper lubrication paths integrated into the housing help maintain performance between scheduled service points.
Integration Guidelines for c 16x60x30x10 500mm Systems
Alignment is critical; mismounted brackets introduce lateral forces that accelerate wear. Use adjustable shims and dial indicators during installation to verify parallelism and perpendicularity.
Control systems should incorporate limit switches and soft stops to protect the 500mm travel range. Cable management features such as sliding chains keep wiring secure and prevent damage during full extension cycles.
Performance Metrics and Testing Results
Bench testing has shown that this module can sustain rated load at full extension with minimal sag. Vibration tests indicate stable behavior up to the specified maximum speed, even when side loads are present.
- Rated stroke of 500mm with 30mm carriage footprint
- Axial load capacity around 120 Newtons in standard conditions
- Repeatability within ±0.05mm across 1000 cycles
- Compatible with common industrial mounting patterns
- Corrosion resistant finish for extended outdoor usability
- Low backlash drive options for precision positioning
Maintenance and Lifecycle Considerations
建立周期性检查计划可以显著延长使用寿命，包括清理碎屑、检查润滑脂状态以及验证紧固件扭矩。记录每次维护的数据有助于预测更换周期并优化备件库存。
操作人员应接受基础培训，了解正确启动与停止流程。避免在超过额定负载或极限速度下运行，以降低意外故障风险并保障设备整体可靠性。
FAQ
Reader questions
如何判断安装基座是否满足该模块的力学要求？
建议在安装孔周围增加加强筋或加厚板材，并确保基座平面度控制在0.1mm以内。这样可以防止在高负载和长行程运行时出现挠曲变形，从而维持导轨的平行度和重复精度。
在500mm全行程下，该模块能否长时间保持标定位移精度？
在规范润滑和预防性维护条件下，该模块可以在全行程范围内维持±0.05mm的重复定位精度。定期检测导轨磨损和预紧力，可以避免因长时间运行导致的精度漂移。
是否可以直接将该模块集成到现有控制柜中？
电气接口通常支持常见的+24V工业信号与差分编码器反馈。接线前需核对电源电压与驱动器匹配，并预留适当的空间以满足500mm行程所需的电缆管理方案。